Malzeme Bilimi ve Mühendisliği Bölümü

Permanent URI for this communityhttps://hdl.handle.net/20.500.12416/18

Browse

Now showing 1 - 6 of 6

Citation - WoS: 25
Citation - Scopus: 27
Crystallization Kinetics and Phase Transformation Mechanisms in Cu56zr44 Glassy Alloy
(Springer, 2015) Kramer, Matthew J.; Napolitano, Ralph E.; Kalay, Ilkay
The kinetics and phase selection mechanisms involved in the crystallization of an amorphous Cu-Zr alloy of eutectic composition (Cu56Zr44) were investigated using in situ high-energy X-ray diffraction (HEXRD), transmission electron microscopy (TEM), and differential scanning calorimetry (DSC) under isothermal and constant heating rate conditions. In situ HEXRD results for 10 K/min (10 A degrees C/min) heating indicate that the amorphous alloy devitrifies into CuZr2 and mainly Cu10Zr7 at the crystallization temperature of 725 K (452 A degrees C). The sequence continues with the precipitation of CuZr (B2) at 1004 K (731 A degrees C), where these three phases coexist until the decomposition of CuZr2 is observed at 1030 K (757 A degrees C). The two equilibrium phases Cu10Zr7 and CuZr (B2) remain present on further heating until melting at the eutectic temperature for the Cu56Zr44 alloy. TEM investigation of the isothermal [705 K (432 A degrees C)] crystallization sequence reveals primary nucleation and growth of the Cu10Zr7 phase, where growth of the Cu10Zr7 crystals is initially planar with a transition to a cellular morphology, associated with partitioning of Zr at the growth front. Related cellular structures and composition profiles are quantified. (C) The Minerals, Metals & Materials Society and ASM International 2015
Citation - WoS: 11
Citation - Scopus: 11
Effect of Sn Alloying on the Diffusion Bonding Behavior of Al-Mg Alloys
(Springer, 2017) Esen, Ziya; Dericioglu, Arcan F.; Atabay, Sila Ece
Effect of Sn as an alloying element on the diffusion-bonding behavior of Al-Mg-Si alloy has been studied by means of differential scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM) and mechanical testing of the diffusion-bonded joint. XRD results revealed the formation of Mg2Sn and (Sn) phases during solidification following induction casting. DSC results showed local liquid (Sn) formation during the bonding process for Sn-containing alloys, where its amount was found to be increasing with the increasing Sn content. Results revealed that Sn addition leads to an increase in the bond shear strength of the diffusion-bonded joints and elimination of the irregularities formed on the bonded interface. Fractured surfaces showed that formation of (Sn) layer at the bonded interface causes the fracture to transform from the ductile to the mixed fracture mode.
Citation - WoS: 21
Citation - Scopus: 25
Experimental Investigation on Wire Electric Discharge Machining of Biodegradable Az91 Mg Alloy
(Springer, 2021) Cogun, Can; Genc, Asim; Esen, Ziya; Bozkurt, Fatih; Urtekin, Levent; Ozerkan, Haci Bekir
The AZ91 magnesium alloy, used commonly as a biodegradable material in biomedical applications, is generally formed by conventional casting method (CCM) and high-pressure die casting method (HPDCM). The AZ91 alloys exhibit poor machinability with conventional chip removal methods since they degrade at elevated temperatures. In this study, the wire electric discharge machining (WEDM) was presented as a candidate process to machine the AZ91 alloy since no cutting stresses and plastic deformations were applied by the cutting tool to the part causing elevated temperatures. In this context, the WEDM machinability of the AZ91 alloy samples produced by cold chamber HPDCM and CCM at different process parameters, was experimentally investigated. The machining performance outputs (the machining current (I), the machining rate (MR), the average surface roughness (R-a), and surface topography) were found for the varying process parameters [pulse time (t(s)), pulse-off time (t(off)), dielectric flushing pressure (P-d), and wire speed (V-w)]. The present study revealed that the I and the MR were significantly dependent on the density, the porosity, and the micro structure of the samples, and the HPDCM samples gave the higher MR and the smoother surface than that of the CCM.
Citation - WoS: 23
Citation - Scopus: 24
Kinetics and Mechanisms of Isothermal Devitrification in Amorphous Cu50zr50
(Springer, 2015) Kalay, Ilkay; Kalay, Y. Eren; Kramer, Matt; Napolitano, Ralph; Cullinan, Tim
The crystallization kinetics and microstructural dynamics associated with devitrifying a melt-spun Cu50Zr50 metallic glass were investigated using isothermal treatments, in situ high-energy synchrotron X-ray diffraction, conventional and high-resolution transmission electron microscopy, and differential scanning calorimetry. The analysis of isothermal transformations allows us to more clearly unravel the complex interplay between nucleation and growth of competing stable and metastable phases. The isothermal devitrification response was found to involve the Cu10Zr7, CuZr2, and CuZr phases, consistent with previously reported constant heating rate experiments, but here we have resolved the phase evolution and structural characteristics of the transformation, including the very early stages of crystallization. At 671 K (398 A degrees C), the isothermal transformation starts with the formation of the Cu10Zr7 phase, which grows in a generally equiaxed morphology. At a size of approximately 100 nm, the growth of the Cu10Zr7 particles is interrupted by the precipitation of a thin layer of the CuZr2 phase, upon which the metastable CuZr (B2) grows epitaxially. Crystallization kinetics are quantified here though in situ measurements (HEXRD, DSC) and ex situ microstructural analysis (TEM, HRTEM). Finally, the influences of chemical partitioning, diffusion, and crystallographic orientation on this sequence are examined.
Kinetics and mechanisms of isothermal devitrification inamorphous cu50zr50
(Springer, 2015) Cullinan, Tim; Kalay, İlkay; Kalay, Y. Eren; Kramer, Matt; Napolitano, Ralph
The crystallization kinetics and microstructural dynamics associated with devitrifying a melt-spun Cu50Zr50 metallic glass were investigated using isothermal treatments, in situ high-energy synchrotron X-ray diffraction, conventional and high-resolution transmission electron microscopy, and differential scanning calorimetry. The analysis of isothermal transformations allows us to more clearly unravel the complex interplay between nucleation and growth of competing stable and metastable phases. The isothermal devitrification response was found to involve the Cu10Zr7, CuZr2, and CuZr phases, consistent with previously reported constant heating rate experiments, but here we have resolved the phase evolution and structural characteristics of the transformation, including the very early stages of crystallization. At 671 K (398 A degrees C), the isothermal transformation starts with the formation of the Cu10Zr7 phase, which grows in a generally equiaxed morphology. At a size of approximately 100 nm, the growth of the Cu10Zr7 particles is interrupted by the precipitation of a thin layer of the CuZr2 phase, upon which the metastable CuZr (B2) grows epitaxially. Crystallization kinetics are quantified here though in situ measurements (HEXRD, DSC) and ex situ microstructural analysis (TEM, HRTEM). Finally, the influences of chemical partitioning, diffusion, and crystallographic orientation on this sequence are examined.
Citation - WoS: 11
Citation - Scopus: 13
Nanocrystallization in Cu-Zr Bulk Metallic Glasses
(Springer, 2018) Yasar, Bengisu; Kalay, Ilkay; Sikan, Fatih
The effect of rare-earth element (Sm) microalloying on the thermal stability and crystallization kinetics of melt-spun ribbons and suction-cast rods of Zr48Cu38.4Al9.6Sm4 alloy were investigated using differential scanning calorimetry (DSC), X-ray diffraction (XRD), transmission electron microscopy (TEM), and atom probe tomography (APT). The XRD results of constant heating rate annealing indicated that amorphous Zr48Cu38.4Al9.6Sm4 melt-spun ribbons devitrifies into Cu2Sm at 673 K (400 A degrees C). The sequence continues with the precipitation of Cu10Zr7 and then these two phases coexist. XRD and TEM studies on 1 mm diameter as suction-cast rods indicated the precipitation of 30-nm-mean size Cu2Sm crystals during solidification. TEM investigation of the isothermal crystallization sequence of melt-spun ribbons and 1-mm-diameter suction-cast rods revealed the precipitation of Cu2Sm nanocrystals at the onset of crystallization and the restriction of the growth of these nanocrystals up to 10 nm diameter with further annealing. APT analysis of 1-mm-diameter suction-cast rods showed that the limited growth of Cu2Sm nanocrystals is due to sluggish diffusion of Sm and Al-Zr pile up at the interface.

Browse

Browsing Malzeme Bilimi ve Mühendisliği Bölümü by browse.metadata.publisher "Springer"