Mekatronik Mühendisliği Bölümü Yayın Koleksiyonu
Permanent URI for this collectionhttps://hdl.handle.net/20.500.12416/255
Browse
4 results
Search Results
Article Citation - WoS: 9Citation - Scopus: 10Effect of Use of Cu-Cr P/M Electrodes on Machining Performance of Electric Discharge Machining(Gazi Univ, Fac Engineering Architecture, 2015) Gulcan, Orhan; Çoğun, Can; Uslan, Ibrahim; Usta, Yusuf; Cogun, Can; Çoʇun, Can; Mekatronik MühendisliğiIn this study, the effect of use of Cu-Cr powder metal (P/M) electrodes on EDM performance outputs, namely material removal rate (MRR), electrode wear rate (EWR), mean and maximum roughness of machined surface (R-a and R-z) and workpiece surface recast layer thickness, was investigated experimentally. The Cu-Cr P/M electrodes produced at different mixing ratios, compacting pressures and sintering temperatures were used to machine SAE 1040 steel. The analyses performed have shown that the electrode material is deposited on to the work surface as a layer and the powder mixing ratio, the compaction pressure and sintering temperature affect the EDM performance outputs.Article Citation - WoS: 4Citation - Scopus: 4Influence of the Material Properties on the Elastic-Plastic Deformation in a Heat Generating Composite Solid Cylinder(Gazi Univ, Fac Engineering Architecture, 2013) Ozturk, Ali; Gülgeç, Müfit; Gulgec, Mufit; Mekatronik MühendisliğiBased on Tresca's yield criterion and its associated flow rule, the elastic-plastic deformation of a centrally heated composite cylinder with fixed ends is investigated by considering the influence of geometric parameters as well as material properties such as yield strength, modulus of elasticity, Poisson's ratio, coefficient of thermal conduction and thermal expansion. In the study, stress, strain and displacement distributions in the composite cylinder made of elastic-perfectly plastic material are derived. Stress distribution and evolution of plastic regions in the composite are presented for different levels of heat generation in the core.Article Citation - WoS: 1Citation - Scopus: 2Classification of Low Probability of Intercept Radar Waveforms Using Gabor Wavelets(Gazi Univ, Fac Engineering Architecture, 2021) Ergezer, HalitLow Probability of Intercept (LPI Radar) is a class of radar with specific technical characteristics that make it very difficult to intercept with electronic support systems and radar warning receivers. Because of their properties as low power, variable frequency, wide bandwidth, LPI radar waveforms are difficult to intercept by ESM systems. In recent years, studies on the classification of waveforms used by these types of radar have been accelerated. In this study, Time-Frequency Images (TFI) has been obtained from the LPI radars waveforms by using Choi-Williams Distribution method. From these images, feature vectors have been generated using Gabor Wavelet transform. In contrast to many methods in the literature, waveform classification has been performed by directly comparing the feature vectors obtained without using any machine learning method. With the method we propose, classification accuracies were obtained at intervals of 2 dB between -20 dB and 10 dB and performed at reasonable classification accuracy rates up to -8 dB SNR value. Better results than the best reported in the literature were obtained for some signal types. The results obtained for all waveform types are given in comparison with the results of the existing methods in the literature.Article Citation - WoS: 10Citation - Scopus: 9The Effect of Powder Mixed and Heated Dielectric on Drilling Performance of Electric Discharge Machining (Edm)(Gazi Univ, Fac Engineering Architecture, 2016) Cogun, Can; Urtekin, Levent; Ozerkan, H. Bekir; Uslan, Ibrahim; Erdem, OguzIn this study, heated silicon oil with added carbon and starch powders was used as dielectric liquid, instead of common hydro-carbon based dielectrics, to obtain better hole surface quality with rotating brass tube electrode in electric discharge machining (EDM). The electro-rheometer tests were conducted to find out the suitable temperature and powder concentration values of the electro-rheological (ER) dielectric under the electric field. Higher workpiece material removal rates (MRR) was obtained in carbon powder added dielectrics than the starch powder added ones for rotating and non-rotating electrodes. The optical microscope observations of the machined hole surfaces indicated that the carbon powder added dielectrics reduced the diameter and depth of the discharge craters, thereby resulting in uniformly distributed and round top peaked surface topography. The starch powder addition to the carbon mixed dielectric further improved the surface quality for both rotating and non-rotating electrodes cases at 30 degrees C and 75 degrees C dielectric temperatures.